中文
English
  - 产品与系统 -
  ·龙牌漆
  ·真石漆
  ·环保涂料
  ·质感涂料
当前位置: 北新涂料 > 质感涂料 >

质感涂料底漆的施工

时间:2014-09-19 13:55 作者:Agnes 点击:
质感涂料底漆的施工 priming conshwction flow 1.方法一:滚涂法;方法二:喷涂法 Method 1:roll coating process method 2: spray coating process 1)滚涂法施工 construction by roll and smear method 施工工具 滚筒 conshwction tool crumbling box 滚涂前

 质感涂料底漆的施工

priming conshwction flow

1.方法一:滚涂法;方法二:喷涂法

Method 1:roll coating process method 2: spray coating process

1)滚涂法施工

construction by roll and smear method

施工工具

滚筒

conshwction tool crumbling box

滚涂前的准备:

preparaton before rolling and smearing

1)清除基层上的异物

clean up the eyewinker on grass roots

2)水性底漆不用加水即可施工,如果需要涂料可加约体积量的10%清水稀释并搅匀

    water priming can be construct -not need to immit the water into it; if need dope,can

immit  10% eau douce of  total volume into it ,and then dilute and mix uniformity

程序及要求

procedure and requirement

用羊毛滚洞将水性底漆采用交义滚涂方法均匀滚刷两遍。

Roll and smear it two times by the method of crossover rolling and smearing with water

priming in the wool rolling hole

    厚度:30微米O.15KG/m}

thickness:30 micron O.15KG/m}

2)喷涂法施工

spray coating process construction

施工工具:底漆喷枪空压机

conshwction tool :priming lance ,air pump

喷涂前的准备

preparation before spraying and smearing

1)清除基层上的异物

clean up the eyewinker on grass roots

2)用于质感涂料的水性底漆不用加水即可施工,如果需要涂料可加约体积量的10%清水稀释并搅匀

    water priming can be construct -not need to immit the water into it; if need dope,can

immit  10% eau douce of  total volume into it ,and then dilute and mix uniformity

程序及要求

procedure and requirement

一{-一

1)、将空压机起动,压力调至8KG,

run the compressor ,and adjust the pressure to 8KG

2)、将水性底漆装入喷枪内,与空压机边接。

Enclose the water priming into the :priming lance ,contact with the side of COI'1'1 pressor

3)、采用十字交义滚涂方法均匀喷刷两遍。

Roll and smear it two times by the method of crossover rolling and smearing with water

priming in the wool rolling hole

4),厚度:30微米O.15KG/m}

thickness:30 micron O.15KG/m}

3.常见问题及处理方法

general problems and disposal method

1)、涂布不均匀:对涂布不均匀的地方要进行修补

COdtlng asymmetry: mend the place of COdtlng asymmetry

2)、基面有接缝上底漆后任有痕迹:应对基面进行修补后再涂底漆。

工fit appear to have ,joints in basic level and marks after smearing priming

in basic level,should re-smearing the priming after mended

4.注意事项:

attention items

1)质感涂料底漆施工时,墙体温度不低于100C,墙面含水率小于10%,空气湿度小于8010

wall body temperature :>100C  ,containing water rate:<10% ,air humidity:<80/0  ,when

construct the priming

2)涂布时应力求均匀。

When coating ,should keep symmetrical

3)不符合技术要求的,修补处理。

Mend it ,if don't fall short of the technology requirements

4)气温5以下不能施工。

Can construct it down 5 0C

网站地图 | 法律声明 | 客户留言 | 网站改版意见反馈联系我们
COPYRIGHT©2008 BNBM ALL RIGHTS RESERVED
更多